I feel like the following scenarios are happening: - 14 ft-lbs is not the correct torque spec. There are many variations a lot of stuff comes from "Factory Only" training, throw in aftermarket parts, the confusion of trying to look something up without the actual vin, and you can see the confusion this creates. Hence the reason new bolts come with the pump. Aluminum does not like crud. The factory thermostat that came out of the old pump has "180" stamped on it. Thermostat housing bolt torque setting? RX-8 Parts For Sale/Wanted. Chevy 5.3 thermostat housing torque specs. Which is why most all Models now have the thermostat housing assembly listed in the maintenance schedule. It's just that Vida in the repair section doesn't mention wheter yo can re-use them or not. 1999 4runner Highlander (Manual). If the surface was roughed up by somebody else then it is probably because they didn't feel like taking time to carefully clean the gasket by hand, and instead used a cordless something. Add in the labor and you can see why some advocate saving a buck on bolts.
Torque Specs For Thermostat Housing And Urban
Last post by Ejbdunes «Replies: 20. Pursuit of accuracy and trying to do things right. Thanks in advance, Greg Sullivan (mailto:[email protected]. My plan will be to torque to 15 ft-lbs, in 2 lbs increments. Applies to screwed joint with strength class readTightening torques (Nm)M5 5 M6 10 M 7 17 M8 24 M10 50 M 12 80 M 14 130.
Torque Specs For Thermostat Housing Opportunity
I can see maybe needing to cut the handles off to get them in tight spaces. I recently replaced it in March. They're not as accurate at the low torque settings. I haven't looked into it. 2 foot pounds in the drawing is 86.
7 Ford Focus Thermostat Housing Torque Specs
And I've never broken one or seen a co-worker break one. If it doesn't look bad, but is bad enough to leak, then judicious use of blue RTV - a skin layer - might save the day, or new parts as the cover is a separate assembly from the housing, which bolts to the engine. And why did you remove every bolt on a 2019? The higher grade HF stuff is supposed to be pretty good. 09-05-2015 08:29 PM. The intake bolts are not angle torqued. Anything which has a soft cork gasket does not need torquing! Torque specs for thermostat housing opportunity. Location: Manitoba, Canada. Is there a torque spec for the housing? You go ten Nm over on one of those small thermostat screws, and I would think it couldn't help but break. I've had many I6 intakes off for alternators (not thermostats because you can do the job with the intake on). It's sunday and every one is closed and I need to get back on the road in the mourning. Member Since: Jun 2001.
Torque Specifications For Thermostat Housing
On many of the newer Volvos these O-rings cost upwards of 50 bucks, can see why people would want to reuse them. Water Pump Pulley Bolts----------------------------------17 – 18 I question this! Coolant Inlet Pipe Nuts-------------------------------------14. I have a few blown out ratchets I need to see if I can still get lifetime warrantied. At any rate I will keep an eye (and a nose) on it after the fix and if I see (smell) a leak I can always tighten the bolts up a little more (if I can get a socket on them! As well as way too many people dicking around with their PCV system BUT forgetting to clean out their oil pan and or change the oil pan O-rings as well as not cleaning out the block to oil pan PCV passages. What's the right torque for thermostat housing bolts. 15 ft*lb is the number I have for the housing in my book, although it doesn't specify if that is housing to block or cover to housing. Since, plastic parts break easily, I'm afraid of over-tightening the bolts. The head gasket job is officially complete: no leaks, runs smoothly, full compression, more power than I've had for over a year. Location: Northern NJ.
Chevy 5.3 Thermostat Housing Torque Specs
I'm thinking that 10nm is for the thermostat cover to housing. Are we taking apart new cars for the fun of it? Last edited by ES6T; 09-19-2018 at 08:40 PM. Thermostat housing torque specs. Fasteners of that ilk aren't usually "torqued". The OP seems to be another one and done. Hybrid Bumper / CBI Hybrid Bumper + Tire Carrier / 4xInnovations Hybrid Sliders / Smittybilt XRC Gen 3 Comp. I did finally figure out that the rubber gasket does not go under or over the goes around it. This a common procedure on many make/model cars.
And including making up your own, apparently. So, you are in danger of snapping them if you are using a 3/8" torque wrench, especially one made by Craftsman between the years of extremely shitty production. Aug 11, 2012 09:22 AM. Also is there a place where I can look up all torque settings so I don't have to bug you guys? Yes, 14 ft lbs is correct.